1. Product Model: JL-712A2H
2. Dimming Output:0~10V dimming interface
3. Certificate: CE, RoHS
4. Compliant Standard: zhaga book18
5. Sensor type: optic sensor + microwave motion
6. infrared remote control to set different parameters
The JL-712A2H light controller product is a smart latch type light controller developed based on the Zhaga Book-18 interface standard. It uses a combination of light sensing and microwave sensing sensors, can output 0-10V dimming signals, and supports infrared remote control for parameter configuration. This light controller is suitable for lighting scenarios such as roads, lawns, courtyards, parks, parking lots, factories, warehouses, etc.
The working logic of the product is that when the illumination is met, the lamp works at a slightly bright brightness and starts a countdown of the slightly bright duration. At this time, if a moving object is detected, the lamp becomes fully bright. When a moving object is detected and left, a countdown of the fully bright duration begins. After the countdown of the fully bright duration ends, it returns to the slightly bright brightness and starts a countdown of the slightly bright duration. When the countdown of the slightly bright duration ends or the illumination is met, the lamp is turned off.
Feature
* 12-24VDC power supply, low power consumption
* Zhaga Book-18 interface standard
* 0-10V dimming mode
* Dynamic adjustment of microwave frequency to avoid mutual interference during dense installation
* Φ 50.4 * 35mm compact size, suitable for installation on various lighting fixtures
* Light sensitivity+microwave, on-demand lighting, more energy-efficient
* Visible light-filtered photosensitive sensor
* High-performance microwave, with a hanging height of 15 meters and an induction radius of ≥10 meters
* Infrared remote control
* IP66
Infrared remote controller
Introduce this Fuction Definition
Note: The infrared remote control controls a distance of about 20 meters, an angle of about ± 45 °, and the display screen has backlight function.
General operating instructions:
4 PIN Definition
Item |
Definition |
Type |
1 |
12-24 VDC |
power input |
2 |
GND / DIM- |
power input |
3 |
NC |
Signal output |
4 |
DIM+ (0-10+) |
Signal output |
Wiring Diagram
Install Diagram
The interface of the product itself has been fool-proof design, the installation only need to tighten the controller directly to the rotatable base, as shown in Figure clockwise after insertion.
Recommended socket selection
Precautions
1. If the negative pole of the auxiliary power supply of the driver is separate from the negative pole of the dimming interface, they need to be short circuited and connected to the light controller # 2.
2. This product is mainly used for LED lamps, tungsten filament lamps and other lamps with a wide spectrum may turn off again after turning on the light.
3. Because the ZHAGA light controller does not have the ability to cut off the AC power supply of the driver, the customer needs to select a driver with an output current close to 0mA when using the ZHAGA light controller, otherwise the phenomenon that the lamp cannot be completely turned off may occur. As shown in the output current curve of the driver specification, the lowest output current is close to 0mA.
4. The light controller only outputs a dimming signal to the driver, regardless of the power load of the driver and light source.
5. When testing, do not use your fingers to block the photosensitive window, as the gaps between your fingers may pass through and cause the light to fail to turn on.
6. After power on initialization, if the lighting illumination and motion trigger conditions have been met, the light will be directly turned on to 100%, and it is not mandatory to enter the stand-by dim level first.
7. There should be no metal objects obstructing the microwave induction radiation angle, otherwise it will seriously reduce the induction performance.
8. If used in outdoor scenes, rain and swaying trees may turn on the light by mistake.
9. Avoid hanging installation to prevent the product from shaking and turn on the light by mistake.
10. The sensing performance will be affected by the installation environment, lighting fixtures, the size and speed of the tester, and the detection range may vary.
11. Infrared remote controls are easily affected by sunlight, so when used outdoors during the day, the remote control distance and other performance may be reduced.
12. The microwave preheating time is 5 seconds, which means that the motion detection signal can only be triggered after the microwave module is powered on for 5 seconds.
Model | JL-712A2H |
Power supply | Voltage:12~24VDC Current:12V/35mA; 24V/25mA |
Power consumption | <0.385W(12V);<0.55W(24V) |
Dimming | 0-10V |
Sensing | light sening+Mircowave |
Microwave frequency | 5.8GHz |
Maximum hanging height | 15 m |
Induction radius | >=10m |
Power on initialization | By default, it remains turn on for 5s (gradient) when powered on, and then runs properly based on parameter Settings and environment conditions |
Sensitivity | Default 80%, adjust through IR |
Hold time | Default 30S, adjust through IR |
Stand-by dim level | Default 0%, adjust through IR |
Stand-by period | Default infinite, adjust through IR |
Turn on Illuminance | Default 50lux, adjust through IR |
Turn off illuminance ∆ value | Default ∆ 50lux, adjust through IR |
Turn off illuminance | Turn on Illuminance + Turn off illuminance ∆ value |
Maximum power ratio | Factory default 100%, adjust through IR |
Off → Stand-by dim time | 0.1s |
Stand-by dim → 100% dim time |
0.1s
When the stand-by dim level is 0%, it lasts for 0.2s, which is |
100% dim → Stand-by dim time |
8s
When the stand-by dim level is 0%, it lasts for 9s, which is |
Stand-by dim → turn off time | 1s |
mechanical vibration | IEC60068-2-6 |
Flammability Level | UL94-V0 |
Storage Temperature | -40 ℃~85 ℃ |
Operating Temperature | -40 ℃~70 ℃ |
Operating Humidity | 5% RH~99% RH |
IP Level | IP66 |
Certifications | CE, ZHAGA, ROHS |
* Turn on Illuminance through APP mode operation.
* you can adjust slowly during time, setting different values of brightness.
* Additionally, this output power ratio is 100% by default, and you can renew the setting or adjust different values via an infrared remote controller.
* you can choose different zhaga series controllers, and also you can choose the lamp luminaire module base type assemblies. such as JL-700, JL-700k3/k4, JL-710, JL-700W, JL-700L, etc.
Model:
At here, we offer a range of Zhaga Book 18 products including Zhaga controllers and assemblies. For example, please refer to the graphic of Zhaga controller product applications on the left side of the page.
zhaga lighting projec
zhaga microwave motion controller
long-join photocell manufacturer
longjoin factory outdoor shooting
Lighting Controller and Component Production Workshop Real Shot
Mastering Zhaga Book-18 Components: Standards, Safety, & Performance in LED Tech
Zhaga JL-700 Zhaga component/Zhaga Book-18 Receptacle
Zhaga book18 accessories (base and cover, sokcet) in barn light install application
Zhaga socket installation/Zhaga Vs Nema receptacle installation
JL700k4/K5 is compliant to NEMA size hole diameter
zhaga soket, zhaga base, zhaga cover
How do wring zhaga socket
Zhaga component
What is the Zhaga book 18?
How to Judge Whether the Light Controller Has a ZHAGA Certificate?
What are the three products of LONG-JOIN that obtained the zhaga certificate first?
It’s a pleasure to assist you. here offer the best latest LONG-JOIN brand Business ranges about NEMA controller, Zhaga control, and smart cities street light controller assemblies. Kindly share your email address with us to receive our heartiest wishes. We are eager to continue this journey as your trusted partner.
JL-250FXA, JL-242JV, JL-260C, JL-207C, JL-208, JL-250F, JL-250G, JL-240XA, JL-205C, JL-103A, JL-403,JL-404C, JL-118A, JL-202 series, and JL-217C, JL-700, JL-700L, JL-711A, etc